Fades and crossfades
Fades smooth the start and end of an audio region. A crossfade blends one region into the next where they overlap, so the join doesn’t click. Every fade change is one undo step.
Add a fade with the Pointer tool
Section titled “Add a fade with the Pointer tool”With the Pointer tool, the top corners of a region are fade zones.
- Move the pointer to the upper-left corner of a region (for a fade-in) or the upper-right corner (for a fade-out). The pointer changes to the fade pointer.
- Drag toward the middle of the region. The fade’s length follows your drag.
To change a fade’s length, drag its end point. Drag it back to the region’s edge to remove the fade.
Use the Fade tool
Section titled “Use the Fade tool”Press ⇧F, or choose Fade Tool from a tool menu.
- Drag inside a region to make a fade. A drag in the left half makes a fade-in, a drag in the right half a fade-out. The length follows your drag.
- Drag across the join between two regions on the same track to make a crossfade between them. This also works when there is a small gap between them.
- ⌥-click a fade to remove it.
Change a fade’s curve
Section titled “Change a fade’s curve”Drag a fade’s line up or down to bend its curve. Dragging down bows the curve down. Dragging up bows it up. With the Pointer tool, hold Control-Shift to reach the curve anywhere along the fade.
You can also type exact values in the Details panel (see below).
Fade settings in the Details panel
Section titled “Fade settings in the Details panel”Select one or more regions and open the Details panel (I). The region section has these fields:
- Fade In and Fade Out: the length in milliseconds. Set a length to 0 to remove that fade.
- Curve: the shape of each fade, from −1 to 1. 0 is a straight line.
- Type (fade-out only): Out, X, EqP or X S.
Some fields are under the panel’s More section in the Wisdom look.
Fade types
Section titled “Fade types”The fade-out’s Type decides what happens where the region overlaps the next one:
| Type | What it does |
|---|---|
| Out | A plain fade-out. The next region gets its own plain fade-in. |
| X | A crossfade with a straight (linear) curve. |
| EqP | An equal-power crossfade. Use it between different material, so the level doesn’t dip in the middle. |
| X S | A crossfade with an S-shaped curve. |
When a fade-out is a crossfade type, it controls both halves of the crossfade. The next region’s Fade In and its Curve are then grayed out, because the crossfade sets them.
Speed Up and Slow Down
Section titled “Speed Up and Slow Down”Click the Fade In label and choose Speed Up, or click the Fade Out label and choose Slow Down. The fade then changes the playback speed instead of the volume, like a tape starting or stopping. Speed fades work on plain fades only, not on crossfades.
Crossfade by dragging regions
Section titled “Crossfade by dragging regions”The Drag menu in the control bar sets what happens when you drag a region over another one on the same track:
-
X-Fade: the overlapping part is crossfaded. This is the default.
-
Overlap: the regions keep their edges. Where they overlap, only the later region plays.
-
Replace: the part of the earlier region that’s covered is removed.
In X-Fade mode, the whole overlap becomes a crossfade as soon as you drop the region. While you drag, a shaded X shows where the crossfade will be. After the drop, the crossfade is drawn as an X across the overlap, even when you are zoomed far out.
If you drag both regions of a crossfade together, the crossfade stays as it was. If you move one region away so they no longer overlap, the crossfade is removed and both edges go back to normal.
While dragging, hold Control to move in steps of the grid division, or Control-Shift to move by single ticks or samples, depending on the zoom.
Crossfade defaults
Section titled “Crossfade defaults”Press ⌥⇧F (Audio Crossfade Options for Merge) to open the Audio Editing window:
- Crossfade Curve: the curve of crossfades made by X-Fade drags. 0 is a straight (linear) crossfade, which keeps the level steady when the same material overlaps, such as a punch-in over the same take.
- Crossfade Time: the default length for fade operations. An X-Fade drag always crossfades the whole overlap, whatever this is set to.
Apply the last fade again
Section titled “Apply the last fade again”Press F (Apply Last Fade or Fade Marquee Selection):
- With regions selected, it copies the last fade you made onto them.
- With a marquee selection, it fades the area you selected.
Fades from Logic projects
Section titled “Fades from Logic projects”When you import a Logic project, region fades and crossfades come in with their Logic type (X, EqP or X S) and their position. Speed Up and Slow Down fades come in as speed fades. Crossfade curves from Logic are not read yet, so check important crossfades by ear.
Related
Section titled “Related”- Splitting regions
- Compadre comping, which adds crossfades at every comp join for you
Logic Pro is a trademark of Apple Inc., registered in the U.S. and other countries. Wisdom Pro is not affiliated with or endorsed by Apple.
Built so far:1,292 hours24.1 billion tokensabout $8,700 at API pricesupdated Nov 21, 2026 What these numbers mean